work until it is reactivated.
This Concept Map, created with IHMC CmapTools, has information related to: Peters_Kernel_Features, Related to EASYFILE this problem popped up: SD CARDS, formated in FAT32 with Windows. (We used fast formating and the complete formating with 4096 and 512 byte blocks, like the standart settings.) Question: Are there any recommendations about the expected format for the SD CARD or which formats and files TACHYON is able to read from SD CARDs with EASYFILE.FTH?, TACHYON COG MODULES (short binaries loaded into spare cog memory) - WS2812 - SD SUPPORT - SPIO - SSD - LTC2754 - 32-channel 8-bit 7.6kHz PWM - PLOT - 32-bit CAPTURE with mask and trigger - RCTIME - WAV PLAY - MCP32xx A/D - 96kBps EEPROM READ AUTO 5/10MHz clock set INTERCOM - Propeller multidrop network 2Mbps with Virtual full-duplex console in parallel with 2Mbps serial console - low level commands to directly access memory etc. ROMS - cog binaries in upper EEPROM - HSUART - full-duplex or high-speed half - UART - F32 floating point - VGA 32x15 - TV - SIDCOG, 16 FOR FGET EMIT NEXT loop body FGET EMIT, *KERNEL FEATURES* *EXTENDED HARDWARE FEATURES*, 0 $40 FS DUMP prepare stack Starting Address : 0 Bytes to dump: $40 (64) DUMP modifier: FS, *EXTENDED HARDWARE FEATURES* ANSI TERMINAL MODES SIMPLE SERIAL up to 250k baud COUNTER MODES - FREQUENCY/TONE GENERATOR HZ KHZ MHZ - RC DAC inc VOLTS setting - EDGE DETECT MODES (i.e. POS EDGE FB DETECT) - PULSE WIDTH MEASUREMENTS AUDIO TONES - BEEPS WARBLE RING LED BLINKER I2C - user set speeds up to 1MHz EEPROM - FETCH/STORE LOAD/SAVE FILL COPY DUMP BACKUP TIMER COG - LINKED USER TIMERS WITH ALARMS etc - HYBRID RTC - SOFT + I2C - FORMATTED DISPLAY - I2C RTC DS3231 DS1307 MCP79410 PCF8563 + compatible variants etc - TIME STAMP - TEMPERATURE KEY POLLS SPI FLASH PING - us or mm reading DHT22 humidity and temperature NEC IR REMOTE TRANSMIT 32 CHANNEL SERVO I2C DEVICE DISCOVERY - lsi2c PIN STATE REPORTING - lsio lists pin states and pull-up/downs, Using EASYFILE another famous one-liner to digest $32 FSADR 32 CTYPE, EASYFILE SD FAT32 - 4 OPEN FILES - VIRTUAL MEMORY ADDRESSING Using EASYFILE, EASYFILE SD FAT32 - 4 OPEN FILES - VIRTUAL MEMORY ADDRESSING Related to EASYFILE this problem popped up:, Using EASYFILE Print Characters in a loop 16 FOR FGET EMIT NEXT, Using EASYFILE Use 8.3 File name format only, *EXTENDED HARDWARE FEATURES* *STANDARD MODULES*, 0 $40 FS DUMP execute command Dumps 64 bytes in HEX and ASCII format, SD CARDS, formated in FAT32 with Windows. (We used fast formating and the complete formating with 4096 and 512 byte blocks, like the standart settings.) Question: Are there any recommendations about the expected format for the SD CARD or which formats and files TACHYON is able to read from SD CARDs with EASYFILE.FTH? As for the matter of formatting there shouldn't be any problems although for some reason Microsoft do not properly implement formatting for Flash devices despite knowing that there should be a difference. If you want to do it properly just as it was formatted in the factory, then try using the formatter from the SD card association itself. (Link attached), *STANDARD MODULES* *EXTRA MODULES*, *EXTRA MODULES* WAV FILE PLAYER W5500 LAN SERVERS (FTP HTTP TELNET) 20x4 CHARACTER LCD QVGA LCD KEYPAD SCANNER - any number and any pins - buffered, decode, and beeps MELODY MORSE SPLAT SERIAL LOGIC ANALYSER VGA BREAKOUT GAME VGA DIGITAL CLOCK & TIMER DISPLAY, *KERNEL FEATURES* 400ns minimum instruction cycle time (80MHz) FAST LOOPING 600ns/loop FAST MULTIPLY ( 7.6us for 12345*12345 ) LMM MODE FAST 4MHz SPI instructions COGSTOP COGINIT COGID CLKSET MODES CODE TIMING TOOLS - LAP .LAP resolve to ns REVECTORABLE CHARACTER I/O ( CONSOLE VGA LCD etc ) ASSIGNABLE KEYBOARD SHORTCUTS, Using EASYFILE dump content 0 $40 FS DUMP, *STANDARD MODULES* EASYFILE SD FAT32 - 4 OPEN FILES - VIRTUAL MEMORY ADDRESSING, 16 FOR FGET EMIT NEXT end loop NEXT